Full Series Wrap-Up: Cracking a 200,000 km 2007 Mitsubishi Outlander 4B12 No-Start
An overdue 200,000 km 2007 Mitsubishi Outlander with a funny crank and zero fault codes—where testing battery, fuel, spark, live data, and in-cylinder pressure waveforms across four interactive episodes uncovered a shifted intake cam and maxed-out timing chain tensioner.
When a 2007 Mitsubishi Outlander with the 4B12 engine rolls in around the 200,000 km mark with skipped oil services and cranks without starting, every guess carries real risk. Chasing the wrong system—or washing cylinder walls with excess fuel and starting spray while guessing at sensors—can turn a saveable high-mileage motor into a much bigger headache.
How Four Episodes Narrowed Down a Stubborn 4B12 No-Start
Across four interactive episodes built around viewer suggestions and real workshop testing, the investigation moved systematically from first impressions to hard proof:
Episode 1 — First Listen & Service Clues: Noted the 200,000 km milestone (202,045 km on the cluster), spotted a service reminder pointing back around 150,000–162,411 km, and captured an unusual cranking sound from both the cabin and open engine bay to set up the diagnostic challenge.
Episode 2 — Battery, Oil, Top-End Spin & Cam/Crank Signals: Charged the battery overnight, verified cranking voltage drop (~11 V minimum) and battery health (~12.8 V after surface charge bleed-off), checked oil level on the dipstick after an earlier low-oil top-up, pulled the rocker cover to confirm both camshafts rotated freely with no seized top end, and scoped intake/exhaust cam signals plus crank/RPM data.
Episode 3 — Codes, 40 ms Pulse Width, Fuel/Spark & MAP vs. MAF: Scanned for trouble codes (finding none after prior battery removal), saw a massive 40 ms injector pulse width on cranking live data, verified fuel pump delivery via scan actuation, tested unplugging injectors with wide-open throttle (getting a kick/fire), checked the 10A coil fuse with a test lamp and scoped coil control, inspected a wet fuel-fouled spark plug, and flagged a steady MAP reading alongside a normal MAF reading.
Episode 4 — Timing Marks, Pressure Transducer, Retiming & Verification: Checked TDC number one and cam/chain timing marks, spotted the intake side out of phase, explained why a standard compression gauge against a ~145 PSI minimum spec can mislead when timing shifts slightly or cylinders wash out, captured an in-cylinder pressure transducer waveform showing a late-closing intake valve, found the old chain tensioner fully extended with the timing cover off, verified valves sealed cleanly without bending, fitted a new tensioner and retimed the engine, rotated two full turns by hand, reset learn values, and confirmed running health plus a post-fix waveform showing intake valve closing around 78.4° after BDC.
From Washed Cylinders to Clean Running and Waveform Proof
On the workshop floor and scope screen, the turning point came when timing alignment, tensioner travel, and in-cylinder pressure waveforms all pointed to the same mechanical truth: an over-extended tensioner and out-of-time intake side rather than a dead battery, bad cam/crank sensor, or seized top end. After retiming with a fresh tensioner, turning the crank two full rotations by hand, clearing codes, and resetting learn values, the 4B12 fired up cleanly with no oil or water leaks, settling short-term fuel trims and showing healthy intake vacuum, zero exhaust restriction, and proper valve timing on the post-fix pressure transducer trace.
Workshop Safety Warning
Always disconnect the battery and support the vehicle securely before removing timing covers, chain tensioners, or camshafts, keep clear of spinning belts/pulleys and rotating cams during cranking checks, handle fuel and starting sprays safely away from ignition sources, and rotate the engine two full turns by hand to verify mechanical clearance before starting.
Series Summary Comparison: What Each Episode Tested and Proved
Episode | Core Focus & Tests | Key Finding / Takeaway | Video Link |
Part 1 | 200,000 km check, service sticker (~150k–162k km), cabin & engine-bay crank sound | Sets up an unusual crank on an overdue 200,000 km Outlander | |
Part 2 | Overnight charge, crank voltage drop (~11 V) & battery test, oil dipstick, rocker cover off, cam/crank scope & scan data | Rules out weak battery, seized top end, and dead cam/crank sensors | |
Part 3 | Code scan, 40 ms injector pulse width, fuel pump actuation, unplugging injectors, 10A coil fuse & scope, wet plug, MAP vs. MAF | Shows heavy fuel/flooding behavior and questions steady MAP vs. engine breathing | |
Part 4 | TDC & timing marks, standard gauge vs. pressure transducer, over-extended tensioner, valve seal check, retiming & post-fix scope | Confirms timing chain/tensioner shift & late intake valve closing; restores clean running |
Don't Stop at Good Signals or Trust a Basic Gauge Blindly
Good cam and crank signals don't guarantee mechanical timing is dead-on—and a basic compression gauge can easily mislead you when timing slips or cylinders wash out, whereas timing verification and in-cylinder pressure waveforms show what is truly happening inside the engine.
Click below to watch the full series from start to finish
Local Workshop & Platform SEO Notes
Service Area: Dead to Alive Engines — engine rebuilding and vehicle diagnostics serving Tīrau, Cambridge, and the Waikato region.
Key Topics & Symptoms Covered: 2007 Mitsubishi Outlander 4B12 crank no start, 200,000 km maintenance & overdue oil service, cranking voltage drop, 40 ms injector pulse width, wet spark plugs, MAP vs. MAF live data, timing chain tensioner extension, standard compression test vs. in-cylinder pressure transducer waveform (78.4° after BDC intake valve closing), and learn value reset.
Shared Mechanical Architecture: Similar 4B12 / MIVEC timing chain, tensioner, fuel/ignition, and in-cylinder pressure waveform diagnostics apply across Mitsubishi Outlander platforms and related Mitsubishi 4B1x engines.
4b11, 4b12, mitsubishi 4b11, mitsubishi 4b12, mitsubishi lancer, mitsubishi asx, mitsubishi outlander, 4b12 no start, 4b11 no start, mitsubishi outlander crank no start, mitsubishi lancer timing chain, mitsubishi asx timing chain, 4b12 timing chain, 4b11 timing chain, mivec timing, crank no start diagnosis, automotive diagnostics, oscilloscope diagnostics, pressure transducer, dead to alive engines, tirau, cambridge nz, waikato mechanic




Comments